-
Color Strip for S-5!® ColorGard® 2.0 -
ColorGard® 2.0 Splice -
ColorGard® 2.0 Unpunched with Splice -
DualClip™ II -
DualClip™ III -
DualCollar™ & DualGard™ Endcap Kit -
DualGard™ Bracket -
1" OD Tube (DualPipe™ alternative) -
1" OD Splice -
GRIPPERFIX® Concealed-Fix (CF) Tab -
GRIPPERFIX® Exposed-Fix (EF) Tab -
GRIPPERFIX® Strut 27" -
GRIPPERFIX® Strut 52" -
#14 - 3" Type A Wood Screw -
Guardian 2 Way Standing Seam Anchor -
Guardian Halo Cable SRL 30ft -
Guardian Halo Cable SRL-LE 25ft -
Guardian Halo Cable SRL-LE 30ft -
Guardian Halo Cable SRL-LE 50ft -
Guardian Norguard 6ft -
Guardian NPH-28 Premium Harness -
Guardian NPH-29 Premium Harness -
Guardian Seraph Construction Harness - XL-XXL -
Guardian Standing Seam Roof Clamp for SRL
Color Strip for S-5!® ColorGard® 2.0
Field-cut 2" metal strip of roofing material.
Description
A strip of roof material inserted into the S-5! ColorGard® 2.0 snow rail to match your roof color. Request color strips 2” wide from roofing panel manufacturer or your authorized S-5! distributor.
We can supply limited colors of strips if required, please advise the QC # from the metal roof manufacturer.
Strips come in 8 ft length.
Colour charts by manufacturer:
ColorGard® 2.0 Splice
Replacement part only, included with ColorGard® 2.0.
ColorGard® 2.0 Unpunched with Splice
Unpunched aluminum bar for ColorGard® 2.0.
Description
Snow Retention | ColorGard® | System Components
Unpunched ColorGard® 2.0 is the most versatile and easy to install, when used with the S-5!® VersaClip™. Unpunched does not need holes, as the VersaClip™ accommodates any seam spacing.
Comes in 7'8" foot length.
DualClip™ II
Snow clip for DualGard™ and VersaGard™ up to 1.5" high.
DualClip™ III
Snow clip for DualGard™ and VersaGard™ above 1.5" high.
DualCollar™ & DualGard™ Endcap Kit
Clean aesthetic that keeps moisture, debris, and pests out.
Description
Fits a 1" pipe.
DualCollar™
Installed on DualPipe at the ends of an assembly, locking DualPipe in place to prevent lateral shifting.
DualGard Endcaps
End caps keep rain, dirt, and debris out of the pipes.
DualGard™ Bracket
DualGard™ 2-pipe snow retention bracket.
Description
DualGard is a two-pipe, 1” diameter (25 mm), aluminum snow bar system that can be used on almost any standing seam metal roof or corrugated metal roof profile.
For standing seam metal roofs, DualGard utilizes two S-5! Mini clamps per bracket to provide a broad attachment base for extra holding strength.
For corrugated metal roofs, DualGard uses the CorruBracket™, providing versatile mounting options.
- One-inch diameter, two-pipe system
- DualGard bracket design provides lateral stability
- Two anchor points per DualGard bracket, for added strength
- Can be used with CorruBracket
Required components, sold separately:
- DualPipe™ (1" tube) with DualGard Splice
- DualClip™ (available in two sizes)
- S-5! Mini clamps (2 per bracket) or CorruBracket™
Resources
- Brochure
- Installation instructions
1" OD Tube (DualPipe™ alternative)
DualPipe™ alternative for DualGard™.
1" OD Splice
Compatible with our 1" OD Tube
Description
GRIPPERFIX® Concealed-Fix (CF) Tab
Connects GRIPPERFIX® to standing seam clamp.
GRIPPERFIX® Exposed-Fix (EF) Tab
Secures GRIPPERFIX® to exposed-fastened panels.
GRIPPERFIX® Strut 27"
27" aluminum mounting strut for securing utilities.
GRIPPERFIX® Strut 52"
52" aluminum mounting strut for securing utilities.
#14 - 3" Type A Wood Screw
Typically used with solid wood framing.
Guardian 2 Way Standing Seam Anchor
Lightweight anchor for standing seam roofs.
Description
The Guardian Fall Protection Two-Way Standing Seam Anchor is a lightweight, reusable roof anchor designed for quick installation and relocation as work progresses. Its non-penetrating design does not compromise roof integrity or damage seams and is compatible with more than 150 standing seam profiles. Made from durable, corrosion resistant aluminum, the Standing Seam Anchor boasts a long service life for increased value on investment.
Product Code: 10600
Guardian Halo Cable SRL 30ft
CSA-certified self-retracting lifeline.
Description
The Guardian Fall Protection Halo Series Self-Retracting Lifeline (SRL) is designed with a specialized quick-action braking system, and is manufactured from non-corrosive, lightweight components. Extremely durable and available with a variety of connector options, Halo SRLs will stand up to even the harshest working conditions.
Product Code: 10915CSA
Guardian Halo Cable SRL-LE 25ft
CSA-certified leading-edge self-retracting lifeline.
Description
The Guardian Fall Protection Halo SRL-LE, formerly the Edge Angel SRL, is designed specifically for Leading Edge (LE) work. It includes an integrated shock absorbing component that helps refocus forces away from the portion of the cable that comes into contact with the edge. While the ideal position for any attachment point is overhead, LE retractables play an important role in the construction industry because, frequently, the only viable attachment point is at foot level. Most SRLs on the marketplace are not certified for such applications, but the Halo SRL-LE is no common SRL, and holds up against even the toughest use.
Product Code: 10922CSA
Guardian Halo Cable SRL-LE 30ft
CSA-certified leading-edge self-retracting lifeline.
Description
The Guardian Fall Protection Halo SRL-LE, formerly the Edge Angel SRL, is designed specifically for Leading Edge (LE) work. It includes an integrated shock absorbing component that helps refocus forces away from the portion of the cable that comes into contact with the edge. While the ideal position for any attachment point is overhead, LE retractables play an important role in the construction industry because, frequently, the only viable attachment point is at foot level. Most SRLs on the marketplace are not certified for such applications, but the Halo SRL-LE is no common SRL, and holds up against even the toughest use.
Product Code: 10925CSA
Guardian Halo Cable SRL-LE 50ft
CSA-certified leading-edge self-retracting lifeline.
Description
The Guardian Fall Protection Halo SRL-LE, formerly the Edge Angel SRL, is designed specifically for Leading Edge (LE) work. It includes an integrated shock absorbing component that helps refocus forces away from the portion of the cable that comes into contact with the edge. While the ideal position for any attachment point is overhead, LE retractables play an important role in the construction industry because, frequently, the only viable attachment point is at foot level. Most SRLs on the marketplace are not certified for such applications, but the Halo SRL-LE is no common SRL, and holds up against even the toughest use.
Product Code: 10927CSA
Guardian Norguard 6ft
Continuous 100% tie-off fall protection.
Description
Guardian 6ft Double Leg Norguard, internal shock absorbing lanyard with regular snap hooks
Product Code: NOR 01-01-6Y
Guardian NPH-28 Premium Harness
Full-body fall arrest harness with pass-through leg straps.
Description
NPH 28 – Premium style harness with pass through legs and chest straps
Product Code: NPH-28
Guardian NPH-29 Premium Harness
Full-body fall arrest harness with belt-style leg straps.
Description
The Guardian NPH full-body harness is the perfect solution for outfitting large crews, roofing, contracting, general industry, and much more. Assembled in Canada, the NPH harnesses are a high-quality fall protection option at an affordable price. These harnesses come available with or without side and shoulder D-rings, along with quick-connect, pass-through, or tongue buckle options to fit any application or need. See complete parts list for more information.
Product Code: NPH-29
Guardian Seraph Construction Harness - XL-XXL
An extra-large full-body fall arrest harness.
Description
- Heavy Duty and Comfortable waist pad with strong belt loops
- Reinforced tool belt which won’t sag or fold under heavy weights
- 2 lanyard keepers
- Durable back placard
- Removable/replaceable back and shoulder padding
- User weight 130-420lb
Product Code: 11171CSA
Guardian Standing Seam Roof Clamp for SRL
Mounts Guardian Leading Edge lifelines up to 50 ft.
Description
The Guardian Fall Protection Standing Seam Roof Clamp is designed for used with SRLs up to 50 feet in length (or up to 65 feet in length if used in combination with the Retractable Swivel Adapter). It functions to attach to metal roof seams spaced from 24 to 36 inches apart, while allowing the attached SRL to rotate a full 360°.
Product Code: 00250
Heat Trace Cable Clip Package of 10
Securely mounts de-icing heat trace cables.
Description
Pack of 10 Clips
The Heat Tape Clip is the ultimate solution for the installation of ice dam heat tape on your standing seam roof. Allowing for easier installation then other standing seam heat tape clips, the SR clip can be installed 3 times faster because the clips can be installed on your S-5 clamps without the cable, and then can be easily adjusted without the need to unscrew hardware. Features a curved cable-grip to prevent sharp metal-edges from cutting into and compromising your heat tape and/or the product warranty. Available in quantities of 10. The S-5 clamp is required to use this product. Not sure which S-5 clamp to use, contact us for assistance
Metal Plus Big Boy
Standing seam scaffolding bracket for 12" aluminum planks.
Description
Metal Plus LLC roof brackets make standing seam metal roof installation safer and faster. The patented, non-penetrating design clamps onto the seam, and rubber pads protect panels from scratches. The brackets work on both mechanical and snap-lock standing seam roofs, which makes them some of the most seam-safe roof jacks available.
- Adjusts from 3/12 to 24/12 slope, one degree at a time, with a double-start crankshaft
- Fits seams from 1″ to 2″ (snap-lock or mechanical)
- Custom rubber pads prevent roof damage
- High-grade powder coating resists corrosion
- Built for 2 × 12 aluminum planks, which lock into place automatically
- Installs with one hand, and goes on and comes off quickly
- 300 lb rating, wet or dry. Meets OSHA requirements when used with proper fall arrest systems and tie-downs.
- Popular with solar installers, carpenters and masons who need a stable, comfortable spot to work for long stretches
Metal Plus Roofer's Helper
Safety bracket for tight spaces where planks won't fit.
Description
The Roofer's Helper Bracket holds solar panels, skylights and chicken ladders securely on standing seam metal roofs, and it fits tight spots where planks won't. Before you buy, check your roof's seam profile, your usual pitch and the load you need.
- Adjustable bar and two clamping systems fit a range of seam widths
- Fits seams from 1″ to 2″ (snap-lock or mechanical)
- Ties down a ladder at the bottom or side of the roof
- Fits tight spaces where planks don't
- Works as steps, so you can climb up the roof and work your way back down
- Holds up to 300 lb, wet or dry
- Custom rubber pads on the base prevent roof damage
- High-grade powder coating resists corrosion
- Suitable for any trade working on standing seam metal roofs
Metal Plus Ultimate Bracket
Standing seam scaffolding bracket for 2″x8″ and 2″x10″s.
Description
Metal Plus LLC roof brackets make standing seam metal roof installation safer and faster. The patented, non-penetrating design clamps onto the seam, and rubber pads protect panels from scratches. The brackets work on both mechanical and snap-lock standing seam roofs, which makes them some of the most seam-safe roof jacks available.
- Adjusts from 3/12 to 24/12 slope, one degree at a time, with a double-start crankshaft
- Keeps the walking platform level at all times, in line with OSHA requirements
- Fits seams from 1″ to 2″ (snap-lock or mechanical)
- Built for 12″ aluminum planks, which lock into place automatically
- Custom rubber pads prevent roof damage
- High-grade powder coating resists corrosion
- Installs and comes off easily with one hand
- 300 lb rating, wet or dry
- Popular with solar installers, carpenters and masons who need a stable, comfortable spot to work for long stretches
PVKIT® 2.0 EdgeGrab Assembly
Secures a single edge on the perimeter of the solar array.
Description
S-5! has introduced a new and improved PVKIT, boasting an improved installation experience for PVmounting technology. The kit comes preassembled with either the MidGrab or EdgeGrab for easier and more efficient installation.
The kits were designed with thread lock on the standoff bolt so that the grab will seat to the PV Module frame by using one tool to drive the top bolt, eliminating a step required in the previous PVKIT. The PVKIT 2.0 features bonding teeth, which are more aggressive to secure a better ground path.
No lugs or wire required except to connect one string of modules to another and to ground the system.
PVKIT® 2.0 EdgeGrab Assembly in Black
Secures a single edge on the perimeter of the solar array.
Description
The S-5!® PV Kit is one of the first solar module mounting solutions in the industry to be listed to the new UL subject 2703, a standard that covers both bonding and mounting. In order to meet the UL requirements, the PV Kit had to be submitted for tests, being evaluated under the severest of conditions to confirm that the product would withstand the elements while maintaining electrical conductivity.
Furthermore, the PV Kit has gained an ETL Listing to UL 1703. UL and ETL listings are widely recognized by most Authorities Having Jurisdiction, which means fewer inspection hassles for installers.
Previously, electrical continuity between modules (called “bonding” within the industry) required the mounting of an electrical lug to each PV module, and interconnection of the lugs with a copper wire. However, the PV Kit's groundbreaking NEW stainless steel mounting disk has twelve nodes designed to ensure the module-to-module conductivity of anodized aluminum module frames.
With the new PV Kit, the module is simply anchored with the kit and automatically provides a ground path in the module frame. No lugs or wire required except to connect one string of modules to another and to ground the system.
In most cases, the savings in time and materials is sufficient to pay for the entire PV Kit and clamp setup! The PV Kit continues to be the easiest, most cost-effective way to install solar panels directly to standing seam metal roofs and remains the most popular choice worldwide
PVKIT® 2.0 MidGrab Assembly
Secures two adjacent solar modules, gripping both edges.
Description
The S-5!® PV Kit is one of the first solar module mounting solutions in the industry to be listed to the new UL subject 2703, a standard that covers both bonding and mounting. In order to meet the UL requirements, the PV Kit had to be submitted for tests, being evaluated under the severest of conditions to confirm that the product would withstand the elements while maintaining electrical conductivity.
Furthermore, the PV Kit has gained an ETL Listing to UL 1703. UL and ETL listings are widely recognized by most Authorities Having Jurisdiction, which means fewer inspection hassles for installers.
Previously, electrical continuity between modules (called “bonding” within the industry) required the mounting of an electrical lug to each PV module, and interconnection of the lugs with a copper wire. However, the PV Kit's groundbreaking NEW stainless steel mounting disk has twelve nodes designed to ensure the module-to-module conductivity of anodized aluminum module frames.
With the new PV Kit, the module is simply anchored with the kit and automatically provides a ground path in the module frame. No lugs or wire required except to connect one string of modules to another and to ground the system.
In most cases, the savings in time and materials is sufficient to pay for the entire PV Kit and clamp setup! The PV Kit continues to be the easiest, most cost-effective way to install solar panels directly to standing seam metal roofs and remains the most popular choice worldwide
PVKIT® 2.0 MidGrab Assembly in Black
Secures two adjacent solar modules, gripping both edges.
Description
The S-5!® PV Kit is one of the first solar module mounting solutions in the industry to be listed to the new UL subject 2703, a standard that covers both bonding and mounting. In order to meet the UL requirements, the PV Kit had to be submitted for tests, being evaluated under the severest of conditions to confirm that the product would withstand the elements while maintaining electrical conductivity.
Furthermore, the PV Kit has gained an ETL Listing to UL 1703. UL and ETL listings are widely recognized by most Authorities Having Jurisdiction, which means fewer inspection hassles for installers.
Previously, electrical continuity between modules (called “bonding” within the industry) required the mounting of an electrical lug to each PV module, and interconnection of the lugs with a copper wire. However, the PV Kit's groundbreaking NEW stainless steel mounting disk has twelve nodes designed to ensure the module-to-module conductivity of anodized aluminum module frames.
With the new PV Kit, the module is simply anchored with the kit and automatically provides a ground path in the module frame. No lugs or wire required except to connect one string of modules to another and to ground the system.
In most cases, the savings in time and materials is sufficient to pay for the entire PV Kit and clamp setup! The PV Kit continues to be the easiest, most cost-effective way to install solar panels directly to standing seam metal roofs and remains the most popular choice worldwide
Includes PV Disk
S-5-E™ Seam Clamp
For traditional 1" and 1.5" tall double-folded seams.
Description
The S-5-E is the heavy-duty S-5! clamp made for traditional double-folded standing seam roofs.
What it fits
- Traditional double-folded seams, 1" and 1-1/2" tall
- A match for profiles like the Butler MR-24
Best for
Mounting snow guards, solar arrays and rooftop utilities on standing seam metal roofs. It's a non-penetrating clamp, so the roof stays intact.
What's included
- M8 bolt x 1
- Setscrews x 2
- Setscrew bit tip for installation
Works with
ColorGard 2.0, X-Gard 1.0, X-Gard 2.0, SKP Snow Diverters, SKP Snow Guard, PVKIT.
Good to know
Need a smaller clamp for solar or DualGard? See the S-5-E Mini Seam Clamp.
Ships duty-free across Canada.
S-5-E™ Mini Seam Clamp
For traditional 1" and 1.5" tall double-folded seams.
Description
The medium-duty S-5-E™ Mini is a non-penetrating seam clamp designed specifically for double-folded standing seam roofs. Smaller and lower cost than the S-5-U™ and S-5-V™ series, but every bit as strong.
The S-5-E™ Mini is shorter than the S-5-E™ with a single setscrew rather than two. Ideal for attaching all kinds of rooftop accessories: signs, walkways, satellite dishes, antennas, rooftop lighting, lightning protection systems, solar arrays, exhaust stack bracing, conduit, condensate lines, and mechanical equipment.
For heavy-duty applications such as snow retention, consider the S-5-E™.
Features:
- Compatible with double-folded, standing seam metal roof profiles
- Compatible with Butler’s MR-24®
- Ideal for light and medium-duty applications
Includes:
- M8 bolt x 1
- T-30 Torx round-point setscrews x 1
- Torx bit tip for installation
S-5-H™ Seam Clamp
Accommodates horizontal seams that are not fully closed.
Description
The S-5-H is a heavy-duty S-5! clamp for standing seam panels with a horizontal seam that isn't fully closed.
What it fits
- Horizontal seams that are not fully closed, up to 0.75" wide
- A two-piece design that can be attached anywhere along the seam
- Side-install setscrews, rather than top-down
Best for
Mounting snow guards, solar arrays and rooftop utilities on standing seam metal roofs. It's a non-penetrating clamp, so the roof stays intact.
What's included
- M8 bolt x 1
- Setscrews x 2
- Setscrew bit tip for installation
Works with
ColorGard 2.0, X-Gard 1.0, X-Gard 2.0, SKP Snow Diverters, SKP Snow Guard, PVKIT.
Good to know
If your horizontal seam is fully closed, the S-5-H90 is the more economical choice. Need a smaller clamp for solar or DualGard? See the S-5-H Mini Seam Clamp.
Ships duty-free across Canada.
S-5-H™ Mini Seam Clamp
Accommodates horizontal seams that are not fully closed.
Description
The S-5-H Mini is the compact, lighter-duty version of the S-5-H for horizontal standing seams that aren't fully closed. It has one setscrew instead of two.
What it fits
- Horizontal seams that are not fully closed, up to 0.75" wide
Best for
DualGard snow guards, solar, satellite dishes and conduit.
What's included
- M8 bolt x 1
- Setscrew x 1
- Setscrew bit tip for installation
Works with
DualGard, PVKIT.
Good to know
Using a Mini clamp for snow retention? DualGard is the snow guard system designed for Minis. For ColorGard or X-Gard, use the standard S-5-H Seam Clamp. The standard clamp also has the two-setscrew design S-5! recommends when holding strength parallel to the seam matters.
Ships duty-free across Canada.
S-5-H90™ Seam Clamp
For horizontal, single-folded seams greater than 0.65” wide.
Description
The S-5-H90 is an economical, heavy-duty S-5! clamp for standing seam panels with a fully closed horizontal, single-folded seam wider than 0.65".
What it fits
- Closed horizontal, single-folded seams greater than 0.65" wide
- A one-piece clamp with top-down setscrews
Best for
Mounting snow guards, solar arrays and rooftop utilities on standing seam metal roofs. It's a non-penetrating clamp, so the roof stays intact.
What's included
- M8 bolt x 1
- Setscrews x 2
- Setscrew bit tip for installation
Works with
ColorGard 2.0, X-Gard 1.0, X-Gard 2.0, SKP Snow Diverters, SKP Snow Guard, PVKIT.
Good to know
If the horizontal seam is not fully closed, use the S-5-H instead. Need a smaller clamp for solar or DualGard? See the S-5-H90 Mini Seam Clamp.
Ships duty-free across Canada.
S-5-H90™ Mini Seam Clamp
For horizontal, single-folded seams greater than 0.65” wide.
Description
The S-5-H90 Mini is the compact, lighter-duty version of the S-5-H90 for closed horizontal, single-folded seams wider than 0.65". It has one setscrew instead of two.
What it fits
- Closed horizontal, single-folded seams greater than 0.65" wide
- A one-piece clamp with top-down setscrews
Best for
DualGard snow guards, solar and rooftop utilities.
What's included
- M8 bolt x 1
- Setscrew x 1
- Setscrew bit tip for installation
Works with
DualGard, PVKIT.
Good to know
Using a Mini clamp for snow retention? DualGard is the snow guard system designed for Minis. For ColorGard or X-Gard, use the standard S-5-H90 Seam Clamp. The standard clamp also has the two-setscrew design S-5! recommends when holding strength parallel to the seam matters.
Ships duty-free across Canada.
S-5-N™ Seam Clamp
Fits mosts nail strip standing seam metal roof profiles.
Description
The S-5-N is the heavy-duty S-5! clamp for popular 1" nail strip standing seam profiles.
What it fits
- 1" nail strip profiles, including Taylor Metals Easy Lock, ASC Building Products Skyline Roofing and NewTech Machinery FF100
- Angled setscrews and an innovative insert fit most nail strip profiles
Best for
Mounting snow guards, solar arrays and rooftop utilities on standing seam metal roofs. It's a non-penetrating clamp, so the roof stays intact.
What's included
- M8 bolt x 1
- Setscrews x 2
- Setscrew bit tip for installation
Works with
ColorGard 2.0, X-Gard 1.0, X-Gard 2.0, SKP Snow Diverters, SKP Snow Guard, PVKIT.
Good to know
Working with a 1.5" nail strip? See the S-5-N 1.5 below. Need a smaller clamp for solar or DualGard? See the S-5-N Mini Seam Clamp.
Ships duty-free across Canada.
S-5-N™ Mini Seam Clamp
Fits mosts nail strip standing seam metal roof profiles.
Description
The S-5-N Mini is the compact, lighter-duty version of the S-5-N for 1" nail strip standing seam roofs. It's a bit shorter and has one setscrew instead of two.
What it fits
- 1" nail strip profiles, including Taylor Metals Easy Lock, ASC Building Products Skyline Roofing and NewTech Machinery FF100
Best for
DualGard snow guards and all kinds of rooftop accessories.
What's included
- M8 bolt x 1
- Setscrew x 1
- Setscrew bit tip for installation
Works with
DualGard, PVKIT.
Good to know
Using a Mini clamp for snow retention? DualGard is the snow guard system designed for Minis. For ColorGard or X-Gard, use the standard S-5-N Seam Clamp. The standard clamp also has the two-setscrew design S-5! recommends when holding strength parallel to the seam matters.
Ships duty-free across Canada.
S-5-N™ 1.5 Seam Clamp
Accommodates most 1.5" narrow nail strip profiles.
Description
The S-5-N 1.5 is the heavy-duty S-5! clamp for popular 1.5" nail strip standing seam profiles. Its wider throat fits most of them without crimping.
What it fits
- 1.5" nail strip profiles, including Bridger Steel 1.5" Tru Snap, Schlebach 1.5" NailStrip, Sheet Metal Supply NS 1.5" and Sheffield Metals SMI 1.5"
- Wider throat, so no crimping is needed
Best for
Mounting snow guards, solar arrays and rooftop utilities on standing seam metal roofs. It's a non-penetrating clamp, so the roof stays intact.
What's included
- M8 bolt x 1
- Setscrews x 2
- Setscrew bit tip for installation
Works with
ColorGard 2.0, X-Gard 1.0, X-Gard 2.0, SKP Snow Diverters, SKP Snow Guard, PVKIT.
Good to know
Is your nail strip's horizontal dimension on the wide side (over 0.475")? Check the S-5-NH 1.5 hinge clamp. Need a smaller clamp for solar or DualGard? See the S-5-N 1.5 Mini Seam Clamp.
Ships duty-free across Canada.
S-5-N™ 1.5 Mini Seam Clamp
Accommodates most 1.5" narrow nail strip profiles.
Description
The S-5-N 1.5 Mini is the compact, lighter-duty version of the S-5-N 1.5 for 1.5" nail strip standing seam roofs. It has one setscrew instead of two.
What it fits
- Most 1.5" nail strip profiles, including Bridger Steel 1.5" Tru Snap, Schlebach 1.5" NailStrip, Sheet Metal Supply NS 1.5" and Sheffield Metals SMI 1.5"
Best for
DualGard snow guards, signs, walkways, satellite dishes, antennas, rooftop lighting and lightning protection systems.
What's included
- M8 bolt x 1
- Setscrew x 1
- Setscrew bit tip for installation
Works with
DualGard, PVKIT.
Good to know
Using a Mini clamp for snow retention? DualGard is the snow guard system designed for Minis. For ColorGard or X-Gard, use the standard S-5-N 1.5 Seam Clamp. The standard clamp also has the two-setscrew design S-5! recommends when holding strength parallel to the seam matters.
Ships duty-free across Canada.
S-5-NH™ 1.5 Seam Clamp
For 1.5" nail strip profiles with wider horizontal dimension.
Description
The S-5-NH 1.5 is a heavy-duty hinge clamp for 1.5" nail strip profiles that have a wider horizontal dimension. ("NH" stands for nail strip hinge.)
What it fits
- 1.5" nail strip profiles with a horizontal dimension over 0.475" and up to 0.800"
- Ideal for Vicwest Prestige, NewTech FF150 and similarly dimensioned profiles
- The hinge insert has a toe that engages the female portion of the panel and forms to the shape of the seam, to help prevent damage at the point of attachment
- The hinge insert is reversible for a proper fit on both wide and medium-width profiles
Best for
Mounting snow guards, solar arrays and rooftop utilities on standing seam metal roofs. It's a non-penetrating clamp, so the roof stays intact.
What's included
- M8 bolt x 1
- Setscrews x 2
- Setscrew bit tip for installation
Works with
ColorGard 2.0, X-Gard 1.0, X-Gard 2.0, SKP Snow Diverters, SKP Snow Guard, PVKIT.
Good to know
Need a smaller clamp for solar or DualGard? See the S-5-NH 1.5 Mini Seam Clamp.
Ships duty-free across Canada.
S-5-NH™ 1.5 Mini Seam Clamp
For 1.5" nail strip profiles with a wider horizontal dimension.
Description
The S-5-NH 1.5 Mini is the compact, lighter-duty version of the S-5-NH 1.5 hinge clamp, with one setscrew instead of two.
What it fits
- 1.5" nail strip profiles with a horizontal dimension over 0.475" and up to 0.800"
- Suits Vicwest Prestige, NewTech FF150 and similarly dimensioned profiles
Best for
DualGard snow guards, solar and rooftop utilities.
What's included
- M8 bolt x 1
- Setscrew x 1
- Setscrew bit tip for installation
Works with
DualGard, PVKIT.
Good to know
Using a Mini clamp for snow retention? DualGard is the snow guard system designed for Minis. For ColorGard or X-Gard, use the standard S-5-NH 1.5 Seam Clamp. The standard clamp also has the two-setscrew design S-5! recommends when holding strength parallel to the seam matters.
Ships duty-free across Canada.
S-5-S™ Seam Clamp
For Snap-Lock, Angle-Seam, and single folded profiles.
Description
The S-5-S is a versatile heavy-duty S-5! clamp for popular snap-together profiles and single-folded angle seams.
What it fits
- Most snap-lock profiles, such as the Firestone UC4 standing seam
- Single-folded (angle-seam) profiles with a horizontal dimension of 0.5" or less
Best for
Mounting snow guards, solar arrays and rooftop utilities on standing seam metal roofs. It's a non-penetrating clamp, so the roof stays intact.
What's included
- M8 bolt x 1
- Setscrews x 2
- Setscrew bit tip for installation
Works with
ColorGard 2.0, X-Gard 1.0, X-Gard 2.0, SKP Snow Diverters, SKP Snow Guard, PVKIT.
Good to know
Need a smaller clamp for solar or DualGard? See the S-5-S Mini Seam Clamp.
Ships duty-free across Canada.
S-5-S™ Mini Seam Clamp
For Snap-Lock, Angle-Seam, and single folded profiles.
Description
The S-5-S Mini is the compact, lighter-duty version of the S-5-S for snap-lock and single-folded angle-seam profiles. It has one setscrew instead of two.
What it fits
- Most snap-lock profiles, such as the Firestone UC4 standing seam
- Single-folded (angle-seam) profiles with a horizontal dimension of 0.5" or less
Best for
DualGard snow guards, solar panels, signs, walkways and other rooftop equipment.
What's included
- M8 bolt x 1
- Setscrew x 1
- Setscrew bit tip for installation
Works with
DualGard, PVKIT.
Good to know
Using a Mini clamp for snow retention? DualGard is the snow guard system designed for Minis. For ColorGard or X-Gard, use the standard S-5-S Seam Clamp. The standard clamp also has the two-setscrew design S-5! recommends when holding strength parallel to the seam matters.
Ships duty-free across Canada.
S-5-T™ Seam Clamp
Designed for "T"-shaped seams up to 1.3" wide.
Description
The S-5-T is a heavy-duty S-5! clamp developed for standing seam profiles with a T-shaped seam.
What it fits
- T-shaped seams up to 1.3" (33 mm) wide
- A match for profiles like the Vicwest Tradition 150 and Garland R-Mer Span
Best for
Mounting snow guards, solar arrays and rooftop utilities on standing seam metal roofs. It's a non-penetrating clamp, so the roof stays intact.
What's included
- M8 bolt x 1
- Setscrews x 2
- Setscrew bit tip for installation
Works with
ColorGard 2.0, X-Gard 1.0, X-Gard 2.0, SKP Snow Diverters, SKP Snow Guard, PVKIT.
Good to know
Need a smaller clamp for solar or DualGard? See the S-5-T Mini Seam Clamp.
Ships duty-free across Canada.
S-5-T™ Mini Seam Clamp
Designed for "T"-shaped seams up to 1.3" wide.
Description
The S-5-T Mini is the compact, lighter-duty version of the S-5-T for T-shaped standing seams. It has one setscrew instead of two.
What it fits
- T-shaped seams up to 1.3" (33 mm) wide
- A match for profiles like the Vicwest Tradition 150 and Garland R-Mer Span
Best for
DualGard snow guards, bracing stack pipes and mechanical fixtures like raceways, and solar.
What's included
- M8 bolt x 1
- Setscrew x 1
- Setscrew bit tip for installation
Works with
DualGard, PVKIT.
Good to know
Using a Mini clamp for snow retention? DualGard is the snow guard system designed for Minis. For ColorGard or X-Gard, use the standard S-5-T Seam Clamp. The standard clamp also has the two-setscrew design S-5! recommends when holding strength parallel to the seam matters.
Ships duty-free across Canada.
S-5-U™ Seam Clamp
Universal clamp suitable for most standing seam profiles.
Description
The S-5-U is our most popular S-5! seam clamp, and the universal one. It fits about 85% of the standing seam profiles made in North America, with no holes in the roof.
What it fits
- Vertical standing seams, and it rotates 90 degrees to fit many horizontal seams
- Most structural (metal building) profiles and most popular architectural profiles
- Heavy-duty grip from two T-30 Torx round-point setscrews
Best for
Mounting snow guards, solar arrays and rooftop utilities on standing seam metal roofs. It's a non-penetrating clamp, so the roof stays intact.
What's included
- M8 bolt x 1
- Setscrews x 2
- Setscrew bit tip for installation
Works with
ColorGard 2.0, X-Gard 1.0, X-Gard 2.0, SKP Snow Diverters, SKP Snow Guard, PVKIT.
Good to know
Installation is simple: place the clamp over the seam and tighten the setscrews. Need a smaller clamp for solar or DualGard? See the S-5-U Mini Seam Clamp.
Ships duty-free across Canada.
S-5-U™ Mini Seam Clamp
Universal clamp suitable for most standing seam profiles.
Description
The S-5-U Mini is the compact, lighter-duty version of the universal S-5-U. It fits the same wide range of standing seam profiles, with one setscrew instead of two.
What it fits
- Vertical standing seams, and it rotates 90 degrees to fit many horizontal seams
- Most structural and architectural standing seam profiles
Best for
DualGard snow guards, solar installs on metal roofs and other rooftop utilities.
What's included
- M8 bolt x 1
- Setscrew x 1
- Setscrew bit tip for installation
Works with
DualGard, PVKIT.
Good to know
Using a Mini clamp for snow retention? DualGard is the snow guard system designed for Minis. For ColorGard or X-Gard, use the standard S-5-U Seam Clamp. The standard clamp also has the two-setscrew design S-5! recommends when holding strength parallel to the seam matters.
Ships duty-free across Canada.
S-5-V™ Seam Clamp
For most machine-folded, vertical, standing seams.
Description
The S-5-V is a cost-effective, heavy-duty S-5! clamp for most machine-folded standing seams in a vertical orientation.
What it fits
- Machine-folded, vertical standing seams within the clamp's dimensions
- Often a lower-cost option than the S-5-U when your seam is a good match
Best for
Mounting snow guards, solar arrays and rooftop utilities on standing seam metal roofs. It's a non-penetrating clamp, so the roof stays intact.
What's included
- M8 bolt x 1
- Setscrews x 2
- Setscrew bit tip for installation
Works with
ColorGard 2.0, X-Gard 1.0, X-Gard 2.0, SKP Snow Diverters, SKP Snow Guard, PVKIT.
Good to know
Not sure the seam is a match? The S-5-U covers a wider range of profiles. Need a smaller clamp for solar or DualGard? See the S-5-V Mini Seam Clamp.
Ships duty-free across Canada.
S-5-V™ Mini Seam Clamp
For most machine-folded, vertical, standing seams.
Description
The S-5-V Mini is the compact, lighter-duty version of the S-5-V for machine-folded vertical standing seams. It has one setscrew instead of two.
What it fits
- Most machine-folded standing seams in a vertical orientation
Best for
DualGard snow guards, walkways, antennas, rooftop lighting, lightning protection systems and solar arrays.
What's included
- M8 bolt x 1
- Setscrew x 1
- Setscrew bit tip for installation
Works with
DualGard, PVKIT.
Good to know
Using a Mini clamp for snow retention? DualGard is the snow guard system designed for Minis. For ColorGard or X-Gard, use the standard S-5-V Seam Clamp. The standard clamp also has the two-setscrew design S-5! recommends when holding strength parallel to the seam matters.
Ships duty-free across Canada.
S-5-Z™ Seam Clamp
For "Zib-Rib" or "Bulb"-shaped standing seams.
Description
The S-5-Z is a heavy-duty S-5! clamp designed for Zip-Rib, Kalzip and other standing seam profiles with a round, bulb-shaped seam.
What it fits
- Zip-Rib, Kalzip and similar bulb-seam profiles
Best for
Mounting snow guards, solar arrays and rooftop utilities on standing seam metal roofs. It's a non-penetrating clamp, so the roof stays intact.
What's included
- M8 bolt x 1
- Setscrews x 2
- Setscrew bit tip for installation
Works with
ColorGard 2.0, X-Gard 1.0, X-Gard 2.0, SKP Snow Diverters, SKP Snow Guard, PVKIT.
Good to know
Need a smaller clamp for solar or DualGard? See the S-5-Z Mini Seam Clamp.
Ships duty-free across Canada.
S-5-Z™ Mini Seam Clamp
For "Zib-Rib" or "Bulb"-shaped standing seams.
Description
The S-5-Z Mini is the compact, lighter-duty version of the S-5-Z for Zip-Rib, Kalzip and similar bulb-seam profiles. It has one setscrew instead of two.
What it fits
- Zip-Rib, Kalzip and similar bulb-seam profiles
Best for
DualGard snow guards, solar and other light-duty installs.
What's included
- M8 bolt x 1
- Setscrew x 1
- Setscrew bit tip for installation
Works with
DualGard, PVKIT.
Good to know
Using a Mini clamp for snow retention? DualGard is the snow guard system designed for Minis. For ColorGard or X-Gard, use the standard S-5-Z Seam Clamp. The standard clamp also has the two-setscrew design S-5! recommends when holding strength parallel to the seam matters.
Ships duty-free across Canada.
CorruBracket™ with M8 Bolt
Versatile mounting bracket for corrugated roofs.
Description
CorruBracket™ can be used to mount almost anything to corrugated metal roofing. CorruBracket is compatible with 7/8" and 3/4" U.S. corrugated profiles. No messy sealants to apply! No chance for leaks! The CorruBracket comes with factory-applied butyl sealant already in the base, and the patented reservoir conceals the sealant from UV exposure, preventing UV degradation.
Includes M8 Bolt.
Protea™ Bracket
Versatile, adjustable bracket for up to 3" trapezoidal ribs.
Description
| Clamps & Brackets | ProteaBracket™ | ProteaBracket
ProteaBracket™ is the most versatile exposed-fastened metal roof attachment solution on the market, fitting most trapezoidal sheet profiles with and without intermediate insulation. It features an adjustable attachment base and multiple solar module attachment options (illustrated below) to accommodate varying widths and heights. There are no messy sealants to apply and no chance for leaks; the ProteaBracket comes with factory applied, adhesive rubber sealant to ensure quick installation and a weather-proof fit.
Installation is simple! The ProteaBracket is mounted directly onto the crown of the panel, straddling the profile. No surface preparation is necessary; simply wipe away excess oil and debris, align, and apply. Secure ProteaBracket through its pre-punched holes, using the hardened drill point screws.
ProteaBracket is the perfect match for the PV Kit and spares you the hassle of cold-bridging! For a solar attachment solution that is both economical and easy to use, choose ProteaBracket.
RibBracket™
Mounting bracket for up to 1" trapezoidal ribs metal roofs.
Description
S-5! RibBracket™ can be used to mount almost anything onto the most common exposed-fastened, trapezoidal roof profi les marketed in North America today. RibBracket is the perfect match for our PV Kit, or any other ancillary application, and eliminates worry about cold bridging! RibBracket is extremely economical and facilitates quick and easy installation. The slotted top hole, which accommodates standard M8 nuts and bolts, simplifi es alignment and maximizes flexibility in attaching ancillaries.
RibBracket™ II
Mounting bracket for up to 1.25" trapezoidal ribs metal roofs.
Description
S-5! RibBracket™ can be used to mount almost anything onto the most common exposed-fastened, trapezoidal roof profi les marketed in North America today. RibBracket is the perfect match for our PV Kit, or any other ancillary application, and eliminates worry about cold bridging! RibBracket is extremely economical and facilitates quick and easy installation. The slotted top hole, which accommodates standard M8 nuts and bolts, simplifi es alignment and maximizes flexibility in attaching ancillaries.
RibBracket™ III
Mounting bracket for up to 1.375" trapezoidal ribs metal roofs.
Description
S-5! RibBracket™ can be used to mount almost anything onto the most common exposed-fastened, trapezoidal roof profi les marketed in North America today. RibBracket is the perfect match for our PV Kit, or any other ancillary application, and eliminates worry about cold bridging! RibBracket is extremely economical and facilitates quick and easy installation. The slotted top hole, which accommodates standard M8 nuts and bolts, simplifi es alignment and maximizes flexibility in attaching ancillaries.
SKP Snow Guard Lower
Base of SKP Snow Guard into one- and two-pipe system.
Description
Lower bracket for a 2 rod system.
Use Stand alone for a 1 rod system..
SKP Snow Guard Upper
Extends SKP Snow Guard into a two-pipe system.
Description
Upper bracket for a 2 rod system.
Must include the SKP-Lower.
7/16" Stainless Steel Stop Collar for SKP Snow Guard
Prevents lateral movement of the SKP Snow Guard rod.
Description
Stop Collar for SnoRod System
SnoBracket™ RB
Attaches ColorGard® to 1" narrow ribbed trapezoidal IMPs.
Description
SnoBracket is a sheeting-only bracket created specifically for trapezoidal-ribbed IMPs, and it comes in two sizes to fit popular rib profile dimensioning. When paired with S-5! ColorGard®, SnoBracket offers an ideal snow retention solution with durable, tested, watertight and proven products.
With no messy, field-applied sealants, there’s no chance for leaks. SnoBracket comes with factory-applied, butyl sealant already in the base. The part design conceals the sealant, preventing UV degradation and over-compression of the sealant when fasteners are secured.
SnoBracket has been rigorously tested parallel-to-seam (drag load) on multiple roofs and thicknesses.
Colorgard crossmember and color strip sold separately.
SnoBracket™ TB
Attaches ColorGard® to 1.22" wide ribbed trapezoidal IMPs.
Description
When mounting snow retention systems to your insulated metal panel (IMP) trapezoidal rib roof, you need attachments built to restrain potentially dangerous accumulated snowpack from avalanching and maintain your panels’ high insulating values without thermal bridging.
SnoBracket is a sheeting-only bracket created specifically for trapezoidal-ribbed IMPs, and it comes in two sizes to fit popular rib profile dimensioning. When paired with S-5! ColorGard® 2.0, SnoBracket offers an ideal snow retention solution with durable, tested, watertight and proven products.
SnoBracket™ protects your roof with factory-applied, premium, closed-cell EPDM rubber gaskets, creating a positive seal against water intrusion. With no messy, field-applied sealants, there’s no chance for leaks.
SnoBracket has been rigorously tested parallel-to-seam (drag load) on multiple roofs and thicknesses.
With no messy, field-applied sealants, there’s no chance for leaks. SnoBracket comes with factory-applied, butyl sealant already in the base. The part design conceals the sealant, preventing UV degradation and over-compression of the sealant when fasteners are secured.
SnoBracket has been rigorously tested parallel-to-seam (drag load) on multiple roofs and thicknesses.
Compatible with the Colorgard™ 2.0 snow retention system.
SnoClip™ 2.0 II
Snow clip for ColorGard® 2.0 on standing seams up to 2" tall.
Description
S-5!® SnoClip™ is an aluminum add-on that helps retard the migration of snow and ice beneath either the ColorGard® crossmember, system. It has a special integrated rubber "foot" to prevent abrasion of the panel's finish. SnoClip slides onto the crossmember or rod and extends down to the flat of the roofing panel.
S-5!® SnoClips™ are highly advised on seams of 2" (50 mm) and higher. They are recommended but not mandatory on seam heights of 1-3/4" and lower (45mm). They retard movement of snow and ice beneath the cross member. SnoClip is not always an option as some metal roofing panels have minor ribs or striations that will not allow the SnoClip to function properly. SnoClips can be used on a striated panel but the results may vary.
SnoClip™ II fits seam heights of 1-3/4" (45mm) and lower.
Typically only one SnoClip per panel is required but may be used more frequently if desired (two SnoClips are needed on panels that have a seam height of 2-3/4" or taller).
SnoClip™ 2.0 III
Snow clip for ColorGard® 2.0 on standing seams up to 3" tall.
Description
SnoClip™ is an aluminum add-on that helps retard the migration of snow and ice beneath either the ColorGard® system. It has a special integrated rubber "foot" to prevent abrasion of the panel's finish. SnoClip slides onto the crossmember or rod and extends down to the flat of the roofing panel.
S-5! SnoClips are highly advised on seams of 2" (50 mm) and higher. They are recommended but not mandatory on seam heights of 1-3/4" and lower (45mm). They retard movement of snow and ice beneath the crossmember. SnoClip is not always an option as some metal roofing panels have minor ribs or striations that will not allow the SnoClip to function properly. SnoClips can be used on a striated panel but the results may vary.
SnoClip III fits seam heights of 1-3/4" to 3" vertical seam.
Their use on other rows is optional and left to user discretion. Typically only one SnoClip per panel is required but may be used more frequently if desired (two SnoClips are needed on panels that have a seam height of 2-3/4" or taller).
SolarFoot™
Pedestal for L-Foot attachment of rail-mounted solar PV.
Description
Introducing the new SolarFoot™ for exposed fastener metal roofing with the strength, testing, quality, and time-proven integrity you expect from S-5!.
View the installation instructions
The SolarFoot provides an ideal mounting platform to attach the L-Foot of a rail-mounted PV system to the roof. This solution is The Right Way to secure rail-mounted solar systems to exposed fastener metal such as AG-Panel or R-Panel.
SolarFoot Features:
- All aluminum and stainless components
- 25yr limited warranty
- Compatible with all commercial L-Foot products on the market
- Factory applied 40-year isobutylene/isoprene crosslink polymer sealant for reliable weathertightness
- Sealant reservoir to prevent over-compression of sealant
- Load tested normal to seam
- Four points of attachment into structure or deck with tested holding strength for engineered applications
- Integrated with M8-1.25x17mm stud and M8-1.25 stainless steel hex flange nut included
The SolarFoot is a simple, cost-effective pedestal for L-Foot (not included) attachment of rail-mounted solar PV. The unique design is compatible with all rail producer L-Foot components. The new SolarFoot assembly ensures a durable weathertight solution for the life of the roof. Special factory applied butyl co-polymeric sealant contained in a reservoir is The Right Way, allowing a water-tested seal. Stainless integrated stud and hex flange lock-nut secure the L-Foot into position. A low center of gravity reduces the moment arm commonly associated with L-Foot attachments. Direct attachment of the SolarFoot to the structural member or deck provides unparalleled holding strength.
Solar Foot Advantages:
- Exposed faster mounting platform for solar arrays attached via L-Foot and Rails
- Weatherproof attachment to exposed fastener roofing
- Butyl sealant reservoir provides long-term waterproof seal
- M8-1.25x17mm stud with M8 hex flange nut for attachment of all popular L-Foot/rail combinations
- Tool: 13 mm Hex Socket or ½”
- Hex Socket
- Tool Required: Electric screw gun with hex drive socket for self tapping screws
- Low Center of Gravity reduces moment arm commonly associated with L-Foot/Rail solar mounting scenarios
- Attaches directly to structure or deck for optimal holding strength
- S-5! Recommended substrate specific e.g. steel purlin, wood 2×4, osb, etc fasteners provide excellent waterproofing and pull out strength
- Fastener through-hole locations comply with NDS (National Design Specification)
*Fasteners sold separately. Fastener type varies with substrate. Contact S-5! on how to purchase fasteners and obtain our test results. L-Foot also sold separately.
Fastener Selection
Fastener selection will depend on whether the supporting structure of the roof is metal or wood.
When relying upon tested load values one of the below fasteners MUST be used. Sold Separately
VersaBracket™ 47
47mm high, bottom-fixed bracket for trapezoidal rib.
Description
The S-5! Versabracket 47 is mounted in the flat of the panel, directly into the supporting structure of the roof, i.e., wood decking, wood or steel purlins, or trusses. No surface preparation is necessary; simply wipe away excess oil and debris, peel the release paper from the base, align and apply. Secure through the pre-punched holes using the appropriate screws (not included) for the supporting structure.
Fasteners not included.
VersaBracket™ 67
67mm high, bottom-fixed bracket for trapezoidal rib.
Description
VersaBracket™ 67 can be used to mount almost anything to an exposed fastened roof system and is compatible with almost any trapezoidal, exposed-fastened profile. No messy sealants to apply! No chance for leaks! The VersaBracket 67 comes with factory-applied butyl sealant already in the base, and the patented reservoir conceals the sealant from UV exposure, preventing UV degradation.
Fasteners not included.
VersaClip™ 2.0
Secures unpunched ColorGard® 2.0 to the clamp/bracket.
Description
The VersaClips™ are inserted into the ColorGard® prior to placement of the ColorGard® on the clamps. Align clips with clamp.
It can be used with all clamps (one per clamp is required)
VersaGard™ Bracket
Direct-attach bracket for ribs up to 1.5".
Description
VersaGard™ V Bracket
Direct-attach bracket for 1.5-2" ribs.
Description
X-Gard™ 1.0 Snow Guard
Max strength, single-pipe snow retention for standing seam.
Description
X-Gard™ 2.0 Snow Guard
Max strength, dual-pipe snow retention for standing seam.
Description
NEX Pipe® with Splice for X-Gard™
Octagonal, high-tensile aluminum cross-pipe for X-Gard™.
Description
Unique, octagonal high-tensile aluminum crossmember spans up to 48". Installs in 7' 8" lengths.
The included splice joins adjacent NEX crossmembers to maintain structural continuity and offer thermal linear expansion and contraction of the X-Gard assembly.
NEX pipe has the ability to cantilever up to 20" past the last clamp in an assembly.
1.9" OD Tube for X-Gard™ (NEX Pipe® alternative)
Cost-effective NEX Pipe® alternative for X-Gard™
1.9" OD Splice
Compatible with 1.9" OD Tube, our NEX Pipe® alternative.
X-Gard™ Endcaps for Nex® Pipe
Clean aesthetic that keeps moisture, debris, and pests out.
Description
Black vinyl end caps keep rain, dirt, and debris out of the pipes.
X-Clip™ II
Snow clip for X-Gard™ on standing seams up to 2" tall.
Description
This aluminum component mitigates the migration of snow and ice beneath the X-Gard™ Pipe. It has a special integrated rubber “foot” to prevent abrasion of the panel’s finish.
X-Clip II™ is designed for seam heights of 1" (25 mm) to 1-3/4" (44.5 mm). It will also fit 2" (51 mm) vertical seams, but not 2" (51 mm) horizontal.
X-Clip™ III
Snow clip for X-Gard™ on standing seams up to 3" tall.
Description
This aluminum component retards the migration of snow and ice beneath the X-Gard™ Pipe. It has a special integrated rubber “foot” to prevent abrasion of the panel’s finish.
X-Clip III™ is designed for seam heights of 2" (51 mm) up to 3" (76 mm).
SKP Snow Diverter for Seams 12"-16" (SD-1216)
Diverts snow around pipes, roof penetrations, and more.
Description
Snow diverter for seams spacing 12"-16.25"
The Snow Diverter is specifically designed to divert the snow and ice away from stacks and vent pipes on metal roofs to avoid unnecessary damage. The Snow Diverter will retain the snow above the roof penetration to prevent excessive loads on the penetrations.
The possibility of vents, flue stacks, or even satellite dishes being destroyed by sliding snow and ice on metal roofs can be nearly eliminated by installing an LMCurbs Snow Diverter utilizing the S-5!® clamps, without penetrating your standing seam roof.
The LMCurbs Snow Diverter is constructed of .125" 3003 aluminum and is fully welded. The standard Snow Diverter is mill-finish aluminum or can be coated to colour-match your roof. The Snow Diverter is installed onto the standing seams of the metal roof using S-5!® clamps. The clamps are constructed of extruded aluminum and utilize stainless steel hardware, limiting the possibility of corrosion. The S-5!® clamp attaches to the panel seam by tightening two “bullet-nosed” stainless steel setscrews against the seam material. The setscrews compress the seam material against the opposite wall of the clamp. They will “dimple” the seam material, but will not penetrate it. S-5!® offers a variety of clamps to accommodate the many profiles on the market today.
Note: Clamps must be installed in accordance with the S-5!® installation instructions.
SKP Snow Diverter for Seams 15.5"-25" (SD-1624)
Diverts snow around pipes, roof penetrations, and more.
Description
Snow diverter for seams spacing 15.5"-25.5"
The Snow Diverter is specifically designed to divert the snow and ice away from stacks and vent pipes on metal roofs to avoid unnecessary damage. The Snow Diverter will retain the snow above the roof penetration to prevent excessive loads on the penetrations.
The possibility of vents, flue stacks, or even satellite dishes being destroyed by sliding snow and ice on metal roofs can be nearly eliminated by installing an LMCurbs Snow Diverter utilizing the S-5!® clamps, without penetrating your standing seam roof.
The LMCurbs Snow Diverter is constructed of .125" 3003 aluminum and is fully welded. The standard Snow Diverter is mill-finish aluminum or can be coated to colour-match your roof. The Snow Diverter is installed onto the standing seams of the metal roof using S-5!® clamps. The clamps are constructed of extruded aluminum and utilize stainless steel hardware, limiting the possibility of corrosion. The S-5!® clamp attaches to the panel seam by tightening two “bullet-nosed” stainless steel setscrews against the seam material. The setscrews compress the seam material against the opposite wall of the clamp. They will “dimple” the seam material, but will not penetrate it. S-5!® offers a variety of clamps to accommodate the many profiles on the market today.
Note: Clamps must be installed in accordance with the S-5!® installation instructions.
SKP Snow Diverter for Seams 22"-25" (SD-24)
Diverts snow around pipes, roof penetrations, and more.
Description
Snow diverter for seams spacing 22"-25"
The Snow Diverter is specifically designed to divert the snow and ice away from stacks and vent pipes on metal roofs to avoid unnecessary damage. The Snow Diverter will retain the snow above the roof penetration to prevent excessive loads on the penetrations.
The possibility of vents, flue stacks, or even satellite dishes being destroyed by sliding snow and ice on metal roofs can be nearly eliminated by installing an LMCurbs Snow Diverter utilizing the S-5!® clamps, without penetrating your standing seam roof.
The LMCurbs Snow Diverter is constructed of .125" 3003 aluminum and is fully welded. The standard Snow Diverter is mill-finish aluminum or can be coated to colour-match your roof. The Snow Diverter is installed onto the standing seams of the metal roof using S-5!® clamps. The clamps are constructed of extruded aluminum and utilize stainless steel hardware, limiting the possibility of corrosion. The S-5!® clamp attaches to the panel seam by tightening two “bullet-nosed” stainless steel setscrews against the seam material. The setscrews compress the seam material against the opposite wall of the clamp. They will “dimple” the seam material, but will not penetrate it. S-5!® offers a variety of clamps to accommodate the many profiles on the market today.
Note: Clamps must be installed in accordance with the S-5!® installation instructions.
#14 - 1 1/2" Type A Wood Screw
Typically used with wood substrates.
#14 - 2 1/2" Type A Wood Screw
Typically used with deeper wood, structural members.
#14-1" Type A/B S/S Screw with EDPM Washer
For weatherproof metal-to-wood or light metal attachment.
#14 - 2" Type A Wood Screw
Typically used with wood decking or purlins.
#14 -1 1/2" Type A PT Wood Screw C/W 2 pc EPDM washer
.500 Torx Set Screw
.625 Torx Set Screw
.900 Torx Set Screw
M8 Hex Flange Bolt 17mm
M8 Hex Flange Nut
All Products
Explore Canada’s largest inventory of non-penetrating S-5!® snow retention systems, solar mounting solutions, rooftop clamps, brackets, and fall protection hardware.